View TSOP36130_4275976.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TSOP361..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
FEATURES
* Photo detector and preamplifier in one package * Internal filter for PCM frequency * Continuous data transmission possible
3 4
16797
* TTL and CMOS compatibility * Output active low * Supply voltage: 2.7 V to 5.5 V * Lead (Pb)-free component * Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC
1
2
MECHANICAL DATA
Pinning 1 = GND, 2 = GND, 3 = VS, 4 = OUT
SPECIAL FEATURES
* Enhanced data rate up to 4000 bit/s * Operation with short burst possible ( 6 cycles/burst) * Taping available for topview and sideview assembly
DESCRIPTION
The TSOP361.. series are miniaturized SMD-IR receiver modules for infrared remote control systems. PIN diode and preamplifier are assembled on lead frame, the epoxy package is designed as IR filter. The demodulated output signal can directly be decoded by a microprocessor. The main benefit is the operation with short burst transmission codes and high data rates at a supply voltage of 3 V. This component has not been qualified according to automotive specifications.
PARTS TABLE
CARRIER FREQUENCY 30 kHz 33 kHz 36 kHz 36.7 kHz 38 kHz 40 kHz 56 kHz SHORT BURSTS AND HIGH DATA RATES (AGC1) TSOP36130 TSOP36133 TSOP36136 TSOP36137 TSOP36138 TSOP36140 TSOP36156
BLOCK DIAGRAM
3 30 k VS 4 Input AGC Band pass Demo dulator OUT
APPLICATION CIRCUIT
17170
Circuit
Transmitter with TSALxxxx
R 1 = 100 TSOPxxxx VS OUT GND VO C1 = 4.7 F C GND + VS
1; 2 PIN
16839
Control circuit
GND
R1 and C1 recommended to suppress power supply disturbances. The output voltage should not be hold continuously at a voltage below VO = 2.0 V by the external circuit.
Document Number: 82191 Rev. 1.6, 20-Aug-08
www.vishay.com 189
TSOP361..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
ABSOLUTE MAXIMUM RATINGS (1)
PARAMETER Supply voltage (pin 3) Supply current (pin 3) Output voltage (pin 4) Output current (pin 4) Junction temperature Storage temperature range Operating temperature range Power consumption Note (1) T amb = 25 C, unless otherwise specified Tamb 85 C TEST CONDITION SYMBOL VS IS VO IO Tj Tstg Tamb Ptot VALUE - 0.3 to + 6.0 3 - 0.3 to (VS + 0.3) 10 100 - 40 to + 100 - 25 to + 85 30 UNIT V mA V mA C C C mW
ELECTRICAL AND OPTICAL CHARACTERISTICS (1)
PARAMETER Supply current Supply voltage Transmission distance Output voltage low Minimum irradiance (30 to 40 kHz) Minimum irradiance (56 kHz) Minimum irradiance (30 to 40 kHz) Minimum irradiance (56 kHz) Maximum irradiance Directivity Note (1) T amb = 25 C, unless otherwise specified Ev = 0, test signal see fig. 1, IR diode TSAL6200, IF = 400 mA IOSL = 0.5 mA, Ee = 0.7 test signal see fig. 1 mW/m2, TEST CONDITION Ev = 0 Ev = 40 klx, sunlight SYMBOL ISD ISH VS d VOSL Ee min. Ee min. Ee min. Ee min. Ee max. 1/2 30 45 0.35 0.4 0.45 0.5 2.7 35 250 0.5 0.6 0.6 0.7 MIN. 0.7 TYP. 1.2 1.3 5.5 MAX. 1.5 UNIT mA mA V m mV W/m2 W/m2 W/m2 W/m2 W/m2 deg
VS = 3 V, pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3 VS = 3 V, pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3 VS = 5 V, pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3 VS = 5 V, pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3 tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3 Angle of half transmission distance
TYPICAL CHARACTERISTICS
Tamb = 25 C, unless otherwise specified
Ee Optical Test Signal (IR diode TSAL6200, IF = 0.4 A, N = 6 pulses, f = f0, t = 10 ms)
0.35
t po - Output Pulse Width (ms)
0.30 Output Pulse 0.25 0.20 0.15 0.10 0.05 0.00 0.1 = 950 nm, optical test signal, fig.1
tpi *) T 6/fo is recommended for optimal function
t
*) tpi
Input Burst Duration
Output Signal VO VOH VOL td1 )
1) 2)
14337
3/f0 < td < 9/f0 tpi - 4/f 0 < tpo < tpi + 6/f0 t
tpo2 )
1
10
100
1000
10 000
16907
Ee - Irradiance (mW/m)
Fig. 1 - Output Function
Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
www.vishay.com 190
Document Number: 82191 Rev. 1.6, 20-Aug-08
TSOP361..
IR Receiver Modules for Remote Control Systems
Vishay Semiconductors
Ee
Ee min. - Threshold Irradiance (mW/m2)
Optical Test Signal
4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 0.01 0.1 1 10 100 Ambient, = 950 nm Correlation with ambient light sources: 10 W/m2 1.4 klx (Std.illum.A, T= 2855 K) 10 W/m2 8.2 klx (Daylight, T = 5900 K)
600 s t = 60 ms Output Signal, (see fig. 4)
600 s
t
94 8134
VO VOH VOL
t on
t off
t
16911
E - Ambient DC Irradiance (W/m 2)
Fig. 6 - Sensitivity in Bright Ambient
Fig. 3 - Output Function
Ton ,Toff - Output Pulse Width (ms)
0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0.1 1 10 100 1000 10 000 = 950 nm, optical test signal, fig. 3 Toff Ton
Ee min. - Threshold Irradiance (mW/m)
1.0
2.0
f = fo 1.5 f = 10 kHz
1.0
f = 1 kHz
0.5 f = 100 Hz 0.0 0.1 1 10 100 1000
16910
E e - Irradiance (mW/m2)
Fig. 4 - Output Pulse Diagram
16912
VsRMS - AC Voltage on DC Supply Voltage (mV)
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
1.2
Ee min. - Threshold Irradiance (mW/m)
2.0
Ee min./Ee - Rel. Responsivity
1.0 0.8 0.6 0.4 0.2 0.0 0.7 0.9 1.1 1.3
f(E) = f0
1.6
1.2
0.8
f = f0 5 % f (3 dB) = f0/7
0.4 0.0 0.0 0.4 0.8 1.2 1.6 2.0
16926
f/f0 - Relative Frequency
94 8147
E - Field Strength of Disturbance (kV/m)
Fig. 5 - Frequency Dependence of Responsivity
Fig. 8 - Sensitivity vs. Electric Field Disturbances
Document Number: 82191 Rev. 1.6, 20-Aug-08
www.vishay.com 191
TSOP361..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
0 1.0 0.9
10
20 30
Max. Envelope Duty Cycle
0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0 20 40 60 80 100 120
16801
40 1.0 0.9 0.8 f = 38 kHz, E e = 2 mW/m 2 50 60 70 0.7 80
0.6
0.4
0.2
0
0.2
0.4
0.6
16914
Burst Length (number of cycles/burst)
d rel - Relative Transmission Distance
Fig. 12 - Directivity
Fig. 9 - Maximum Envelope Duty Cycle vs. Burst Length
Ee min. - Threshold Irradiance (mW/m)
0.6 0.5 0.4 0.3 0.2 0.1 0.0 - 30 - 15 0 15 30 45 60 75 90
17185
1.0 0.9
Ee min. - Sensitivity (mW/m 2 )
Sensitivity in dark ambient
0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
16918
Tamb - Ambient Temperature (C)
VS - Supply Voltage (V)
Fig. 13 - Sensitivity vs. Supply Voltage
Fig. 10 - Sensitivity vs. Ambient Temperature
1.2
S ( ) rel - Relative Spectral Sensitivity
1.0 0.8 0.6 0.4 0.2 0.0 750 850 950 1050 1150
16919
- Wavelength (nm)
Fig. 11 - Relative Spectral Sensitivity vs. Wavelength
www.vishay.com 192
Document Number: 82191 Rev. 1.6, 20-Aug-08
TSOP361..
IR Receiver Modules for Remote Control Systems
SUITABLE DATA FORMAT
The circuit of the TSOP361.. is designed so that unexpected output pulses due to noise or disturbance signals are avoided. A bandpass filter, an integrator stage and an automatic gain control are used to suppress such disturbances. The distinguishing mark between data signal and disturbance signal are carrier frequency, burst length and duty cycle. The data signal should fulfill the following conditions: * Carrier frequency should be close to center frequency of the bandpass (e.g. 38 kHz) * Burst length should be 6 cycles/burst or longer * After each burst which is between 6 cycles and 70 cycles a gap time of at least 10 cycles is necessary * For each burst which is longer than 1.8 ms a corresponding gap time is necessary at some time in the data stream. This gap time should be at least 6 times longer than the burst * Up to 2200 short bursts per second can be received continuously Some examples for suitable data format are: NEC code, Toshiba Micom Format, Sharp code, RC5 code, RC6 code, RCMM code, R-2000 code, RECS-80 code. When a disturbance signal is applied to the TSOP361.. it can still receive the data signal. However the sensitivity is reduced to that level that no unexpected pulses will occur. Some examples for such disturbance signals which are suppressed by the TSOP361.. are: * DC light (e.g. from tungsten bulb or sunlight) * Continuous signal at 38 kHz or at any other frequency * Signals from fluorescent lamps with electronic ballast (see figure 14)
0
16920
Vishay Semiconductors
IR Signal
IR Signal from Fluorescent Lamp with Low Modulation
5
10
15
20
Time (ms)
Fig. 14 - IR Signal from Fluorescent Lamp with Low Modulation
Document Number: 82191 Rev. 1.6, 20-Aug-08
www.vishay.com 193
TSOP361..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
PACKAGE DIMENSIONS in millimeters
16629
ASSEMBLY INSTRUCTIONS
Reflow Soldering * Reflow soldering must be done within 72 h while stored under a max. temperature of 30 C, 60 % RH after opening the dry pack envelope * Set the furnace temperatures for pre-heating and heating in accordance with the reflow temperature profile as shown in the diagram. Excercise extreme care to keep the maximum temperature below 260 C. The temperature shown in the profile means the temperature at the device surface. Since there is a temperature difference between the component and the circuit board, it should be verified that the temperature of the device is accurately being measured * Handling after reflow should be done only after the work surface has been cooled off Manual Soldering * Use a soldering iron of 25 W or less. Adjust the temperature of the soldering iron below 300 C * Finish soldering within 3 s * Handle products only after the temperature has cooled off
www.vishay.com 194
Document Number: 82191 Rev. 1.6, 20-Aug-08
TSOP361..
IR Receiver Modules for Remote Control Systems
VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE
300 250 200 T (C) max. 20 s 150 max. 120 s 100 max. Ramp Up 3 C/s 50 0 0
19800
Vishay Semiconductors
255 C 240 C 217 C
max. 260 C 245 C
max. 100 s max. Ramp Down 6 C/s
50
100
150 t (s)
200
250
300
max. 2 cycles allowed
TAPING VERSION TSOP..TT Dimensions in millimeters
16584
Document Number: 82191 Rev. 1.6, 20-Aug-08
www.vishay.com 195
TSOP361..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
TAPING VERSION TSOP..TR Dimensions in millimeters
16585
www.vishay.com 196
Document Number: 82191 Rev. 1.6, 20-Aug-08
TSOP361..
IR Receiver Modules for Remote Control Systems
REEL DIMENSIONS in millimeters
Vishay Semiconductors
16734
LEADER AND TRAILER Dimensions in millimeters
Trailer
no devices devices
Leader
no devices
End
Start
min. 200
min. 400
96 11818
COVER TAPE PEEL STRENGTH
According to DIN EN 60286-3 0.1 to 1.3 N 300 10 mm/min. 165 to 180 peel angle
LABEL
Standard bar code labels for finished goods The standard bar code labels are product labels and used for identification of goods. The finished goods are packed in final packing area. The standard packing units are labeled with standard bar code labels before transported as finished goods to warehouses. The labels are on each packing unit and contain Vishay Semiconductor GmbH specific data.
Document Number: 82191 Rev. 1.6, 20-Aug-08
www.vishay.com 197
TSOP361..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
VISHAY SEMICONDUCTOR GMBH STANDARD BAR CODE PRODUCT LABEL (Finished Goods)
PLAIN WRITING Item-description Item-number Selection-code LOT-/serial-number Data-code Plant-code Quantity Accepted by Packed by Mixed code indicator Origin LONG BAR CODE TOP Item-number Plant-code Sequence-number Quantity Total length SHORT BAR CODE BOTTOM Selection-code Data-code Batch-number Filter Total length ABBREVIATION INO SEL BATCH COD PTC QTY ACC PCK MIXED CODE xxxxxxx+ TYPE N N X N TYPE X N X LENGTH 18 8 3 10 3 (YWW) 2 8 Company logo LENGTH 8 2 3 8 21 LENGTH 3 3 10 1 17
DRY PACKING
The reel is packed in an anti-humidity bag to protect the devices from absorbing moisture during transportation and storage.
Aluminum bag
Label
After more than 72 h under these conditions moisture content will be too high for reflow soldering. In case of moisture absorption, the devices will recover to the former condition by drying under the following condition: 192 h at 40 C + 5 C/- 0 C and < 5 % RH (dry air/nitrogen) or 96 h at 60 C + 5 C and < 5 % RH for all device containers or 24 h at 125 C + 5 C not suitable for reel or tubes. An EIA JEDEC standard JESD22-A112 level 4 label is included on all dry bags.
Reel
15973
FINAL PACKING
The sealed reel is packed into a cardboard box. A secondary cardboard box is used for shipping purposes.
RECOMMENDED METHOD OF STORAGE
Dry box storage is recommended as soon as the aluminum bag has been opened to prevent moisture absorption. The following conditions should be observed, if dry boxes are not available: * Storage temperature 10 C to 30 C * Storage humidity 60 % RH max.
www.vishay.com 198
16943
Example of JESD22-A112 level 4 label
Document Number: 82191 Rev. 1.6, 20-Aug-08
TSOP361..
IR Receiver Modules for Remote Control Systems
ESD PRECAUTION
Proper storage and handling procedures should be followed to prevent ESD damage to the devices especially when they are removed from the antistatic shielding bag. Electro-static sensitive devices warning labels are on the packaging.
Vishay Semiconductors
VISHAY SEMICONDUCTORS STANDARD BAR CODE LABELS
The Vishay Semiconductors standard bar code labels are printed at final packing areas. The labels are on each packing unit and contain Vishay Semiconductors specific data.
16962
Document Number: 82191 Rev. 1.6, 20-Aug-08
www.vishay.com 199
TSOP361..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
OZONE DEPLETING SUBSTANCES POLICY STATEMENT
It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances (ODSs). The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively. 2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency (EPA) in the USA. 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively. Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances.
We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany
www.vishay.com 200
Document Number: 82191 Rev. 1.6, 20-Aug-08
Legal Disclaimer Notice
Vishay
Disclaimer
All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000 Revision: 18-Jul-08
www.vishay.com 1

▲Up To Search▲

Price & Availability of TSOP36130

	To Download TSOP36130 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .